Fiberglass Pool Installation in Martin County, Florida
Sensassion Pools and Spa offers fiberglass pool installation in Martin County, Florida, from Stuart to Hobe Sound. Our own licensed crew handles the permit, the dig, the crane set and the deck. Installed pools start at $37,990. Once the permit is approved, most yards need about three weeks of site work.We build for the way the Treasure Coast actually works. That means sandy soil and a shallow water table. It also means salt air off the Indian River Lagoon and a long hurricane season. This page covers costs, steps, permits and local site issues, so you can plan with real numbers.

Quick facts
- Starting price: $37,990 installed for X-Pools, and Latham pools from $44,162
- Included: salt system, variable speed pump, wireless automation, dirt removal, electrical subpanel, engineer plan and permit coordination
- Build time: about three weeks of site work after permit approval
- License: Florida Certified Pool/Spa Contractor CPC1461254
- Showroom: 2550 Okeechobee Blvd, Unit G2, West Palm Beach, under an hour south of Stuart on Interstate 95
Fiberglass vs Gunite Pools for Martin County Homes
Most Martin County homeowners compare two pool types: fiberglass and gunite. A gunite pool is concrete sprayed over a steel frame, then finished with plaster. A fiberglass pool arrives as one factory built shell. We lift it into place with a crane.Both can last for decades. The real differences show up in build time, upkeep and how each one handles our climate.
| Feature | Fiberglass | Gunite |
|---|---|---|
| Build time | About three weeks of site work | Often several months |
| Surface feel | Smooth gelcoat | Rough plaster |
| Algae | Nonporous surface resists it | Porous plaster gives algae a place to grip |
| Resurfacing | Not needed for normal wear | Plaster needs redoing over time |
| Salt systems | Works well with salt | Salt can wear plaster faster |
| Shape | Set factory designs | Any custom shape |
Can You Put a Fiberglass Pool in an Existing Pool?
Yes, in many cases. We break out or remove the old pool, then prepare a new base for the shell. Many older gunite and vinyl liner pools around Stuart and Port Salerno are good candidates. We quote old pool removal separately, because every old pool is different.
How Much Does an Inground Fiberglass Pool Cost in Martin County?
Fiberglass pool cost with Sensassion starts at $37,990 installed. Your final price depends on the model, the deck, an enclosure and your site. Here are real starting prices from our current lineup.
| Pool model | Size | Starting price, installed |
|---|---|---|
| X-Pools Naples | 13 to 26 ft long | $37,990 |
| Latham Milan 8.14 (plunge pool) | 14 x 8 ft | $44,162 |
| Latham Tuscan 11.20 | About 20 x 11 ft | $49,622 |
| Latham Olympia 16 (lap pool) | 35 x 16 ft | $72,451 |
| Latham Astoria 14 (pool and spa) | 35 x 14 ft | $83,832 |
Every installed price includes these items:
- Salt water system
- Variable speed pump
- Wireless automation
- Dirt removal from your property
- Electrical subpanel
- Engineer plan and permit coordination
Why Hire Local Swimming Pool Contractors in Martin County?
A pool is a major build on your property. The people who dig it should be the same people who answer your call later. Sensassion does not sell your project to a subcontractor. Our own crew does the work.
- Licensed in Florida: We work under Certified Pool/Spa Contractor license CPC1461254. You can verify any contractor license with the Florida Department of Business and Professional Regulation.
- Real experience: Our founder, Florian Jolly, has installed more than 700 pools over 20 plus years.
- Rated by customers: We hold a 4.9 star rating from 61 Google reviews.
- Already working here: Our team has delivered and installed hot tubs for homeowners in Stuart and Jensen Beach.
- Help after the build: We also offer once your new pool is running.
What to Expect When Putting In a Fiberglass Pool
Putting in a fiberglass pool follows a clear order, and each step moves quickly. Here is our fiberglass pool installation process for a Martin County home.
Step 1: Site Visit and Plan
We walk your yard and check crane access from the street. We look at setbacks, drainage, septic lines and where the equipment will sit. Then we help you pick a shell and lay out the pool.
Step 2: Permit and Engineer Plan
We prepare the engineer plan and submit it to the right building office. If your home is in an HOA, we prepare drawings for its review board too. This step often takes about a week, depending on the office.
Step 3: Utility Locates
Florida law requires a call to Sunshine 811 at least two full business days before digging. Utility companies then mark the buried lines in your yard. We place this request for you.
Step 4: Dig, Base and Crane Set
We dig the hole and lay a compacted crushed stone base. A crane lifts the shell over your house or fence and sets it level. The dig through backfill usually takes about five days.
Step 5: Plumbing, Bonding and Backfill
We connect the plumbing and bond the pool to the electrical grid. Then we fill the pool with water and backfill around it at the same pace. This keeps pressure even on the shell walls.
Step 6: Collar, Deck and Final Inspections
We pour the concrete collar and build your deck, which takes about a week. Inspectors then check the barrier, the electrical work and the final build. Last, we start the equipment and show you how it all works.
Fiberglass Pools Near Me: Where We Install in Martin County
We offer fiberglass pool installation in Martin County, Florida, in every town and neighborhood. Each area has its own soil, access and permit rules. Here is what we plan for in each one.
Stuart and Sewall’s Point
Stuart homes range from older lots in Rio and North River Shores to newer builds off Kanner Highway. Many sit near the St. Lucie River, where groundwater runs close to the surface. Sewall’s Point sits between the St. Lucie River and the Indian River Lagoon. Its narrow lots off Sewall’s Point Road often need careful crane planning. The City of Stuart and the Town of Sewall’s Point each review their own permits.
Palm City
Palm City yards in Martin Downs and Piper’s Landing tend to be larger. Many have room for a pool and spa combo. Homes along the South Fork of the St. Lucie River share Stuart’s high water table. Most Palm City projects go through the Martin County Building Department.
Jensen Beach and Hutchinson Island
Homes off Jensen Beach Boulevard and NE Indian River Drive deal with salt air every day. So do homes on Hutchinson Island. Choose stainless or coated hardware, and place equipment out of the direct ocean wind. A screen enclosure also keeps leaves and blowing sand out of the water.
Hobe Sound and Jupiter Island
Hobe Sound lots off SE Bridge Road and near Jonathan Dickinson State Park often sit on deep, loose sand. That makes digging easy, but the shell needs firm support during backfill. Jupiter Island has its own town building office for permits.
Port Salerno
Port Salerno homes sit near the Manatee Pocket and SE Salerno Road. Many lots are older and tighter, with mature trees and close neighbors. We check crane reach and overhead lines early, so install day stays on track.
Indiantown
Indiantown sits inland along SW Warfield Boulevard, closer to Lake Okeechobee. Larger rural lots give plenty of room, but summer rains can flood low ground. The Village of Indiantown issues its own pool permits, plus a separate barrier permit.
Not sure if we reach your street? Call us at (561) 685 1315 or check our .
Small Inground Pools and Fiberglass Plunge Pools
Not every yard has room for a 35 foot lap pool. Small inground pools fit tight lots, zero lot line homes and yards with an existing screen enclosure. They also cost less to heat and run each month.
- Latham Milan 8.14: a 14 x 8 ft fiberglass plunge pool, from $44,162. It works well for cooling off and soaking.
- X-Pools Naples: lengths from 13 to 26 ft, from $37,990. This is our lowest starting price.
- Latham Tuscan 11.20: about 20 x 11 ft, from $49,622. Kids get room to swim, and adults get room to relax.
A plunge pool also suits retirees who want gentle, low impact exercise at home. Add a heat pump, and you can keep swimming through our cooler winter months.
Fiberglass Pool Shells, Brands and Gelcoat Colors
A fiberglass pool shell is one molded piece. Its inside layer is gelcoat, a hard, smooth finish that gives the pool its color. We install shells from two manufacturers.
- : 45 models, with 41 pools and 4 spas, in six shell colors. Latham backs its shells with a limited lifetime structural warranty, and its terms apply.
- : 10 models in 30 sizes, plus 2 spa models. X-Pools offers clean, modern lines and our lowest starting prices.
Darker shell colors make the water look deep blue. Lighter colors give a bright, clear look closer to the ocean off Stuart Beach. Photos never quite match real life, so compare the colors in person at our .
Building for Martin County Soil, Water Table and Storms
This is where local experience matters most. Martin County’s ground and weather shape every step of the build.
High water table. Groundwater sits close to the surface across much of the county, especially near the St. Lucie River and the Indian River Lagoon. It rises even higher during the wet season. We pump groundwater down while we dig and set the shell. After the build, never drain a fiberglass pool on your own. An empty shell can lift or shift when the ground is wet.
Sandy soil. Most of coastal Martin County sits on loose sand. Sand drains well, but it moves easily. A firm crushed stone base and steady backfill keep the shell level for years.
Hurricanes. Atlantic hurricane season runs from June 1 to November 30. In 2004, Hurricanes Frances and Jeanne both came ashore near Stuart. A filled, backfilled fiberglass pool is heavy and stays put in high wind. Before a storm, keep the water in, shut off power to the equipment and bring in loose furniture.
Wind rules for enclosures. Martin County sits in a wind borne debris region under the Florida Building Code. Screen enclosures need their own permit and must meet local wind design rules.
Can a Fiberglass Pool Be Installed Partially Above Ground?
Yes. A semi inground pool sits partly above the yard, with raised walls around the top edge. This works well on lots with a very high water table. The raised edge can also double as a seat wall. Your engineer plan must show how those raised walls get support.
Can You Install a Fiberglass Pool on a Slope?
Yes, with the right prep. We cut into the slope or build up the low side, then hold the soil with a retaining wall. Martin County requires a separate permit for a retaining wall. Most local lots are flat, so this comes up mainly on raised riverfront and ridge properties.
Martin County Pool Permits, HOA Approval and Safety Rules
Every new pool in Martin County needs a building permit. The pool barrier needs its own permit too. We handle the paperwork, but it helps to know what the rules say.
Which office reviews your permit. Unincorporated areas like Palm City, Jensen Beach, Hobe Sound and Port Salerno use the Martin County Building Department. It sits at 900 SE Ruhnke Street in Stuart. The City of Stuart, Sewall’s Point, Jupiter Island, Ocean Breeze and Indiantown each run their own building offices.
What state law requires. Florida’s Residential Swimming Pool Safety Act is Chapter 515 of the Florida Statutes. It requires at least one safety feature before your pool can pass final inspection. Your options include:
- A barrier at least 4 feet high, with gates that open outward and latch on their own
- An approved safety pool cover
- Exit alarms on all doors and windows that open to the pool
- Self closing, self latching doors with the release at least 54 inches above the floor
- A pool alarm certified to ASTM standard F2208
We also offer pool maintenance in Martin County.